Parts & Accessories
The Wahoo RPM speed sensor is the sleek, magnet-less solution for capturing cycling speed data. It easily mounts to your bike's front wheel hub, and the Bluetooth Smart and ANT+ dual band technology allow you to connect to and display data on both smartphones and bike computers. Tracking speed data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - The RPM speed installs easily with no magnets required - It only weighs 16.5 grams with the mount included - Provides accurate speed data during your ride - Mounts on most front wheel hub with a secure silicone casing - Two LED lights show the sensor's device connection (blue) and speed detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM Speed will fit with most bikes and frame sizes
SRAM eTap batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes just 45 minutes to complete. - Finish: Black - Compatibility: SRAM RED eTap
SRAM eTap Battery is the power source for the eTap system. The same power unit is interchangeable between front and rear derailleurs. - Up to 1000 kilometers of riding per charge - Weight: 24g - Finish: Black - Compatibility: SRAM RED eTap
- A great way to mount a light, computer, power meter or GPS unit in the center of a threadless stem - Made in the USA - Material: 6061 Aluminum - Weight: 24g - Outside Diameter: 26.0mm - Stem Size: Threadless 1-1/8"
KMC's digital ChainChecker is the most accurate tool for checking your chain’s elongation. - Measures up to 2.5mm elongation - Fits all chains including 11 speed - Handy electronic device - Stainless hardened metal body
The K-EDGE Garmin Stem Mount is a great upgrade solution for cyclists who prefer their computer above the stem. Mounting off of the steerer tube, the mount replaces a standard 5mm spacer, and is locked securely in place by the top cap compression system. The fixed version is recommended for zero degree or negative degree stem angles. Can also be used with positive degree stems if additional spacers added (5mm to 10mm) above the stem. Designed with mountain biking in mind, the K-EDGE Stem mount is also ideal for much more including: cyclocross; triathlon; bike touring; or if you simply prefer this position for your computer. - Compatibly – 1-1/8" Steerer tube Diameter, Thickness (@ Steerer) – 5mm, Length (Center-to-Center) – 50mm, - Recommended for 0 Degree to Negative Degree Stem Angles - Supported Computers – Garmin Edge 20, 25, 200, 500, 510, 520, 800, 810, and Forerunner 310XT - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded.
$49.99 - $54.99
This is K-Edge's next generation of industry-leading Garmin Computer Mounts—stronger, easier, more versatile, and more stylish design to complement your Garmin and your bike. The ultimate upgrade for your Garmin computer. Their advanced co-polymer Garmin insert locks your computer in place with strength and security. Designed and tested extensively so that the replaceable insert breaks away instead of your computer tabs in the event of a crash or mishap. - CNC Machined 6061 T6 Aluminum - Compatibility – 31.8mm and 35mm diameter handlebars. - New clamp design is hinged for ease of installation. - Supported Computers – Most Garmin Edge, Forerunner, and Touring models, including the new Garmin Edge 520, Edge 20 and Edge 25 models (Edge 1000 - fits on the longer XL mount) - Combo Compatible – versions available that support GoPro style interface action cameras and lights - Weight – (31.8 mm) Standard Mount 45.4 grams; Combo Mount 55.4 grams Attention: ASSEMBLY BOLTS NOT MEANT TO BE REMOVED OR TAMPERED WITH AT ANY TIME. *TheNEW K-EDGE Handlebar Computer and Camera Mounts (1420, 1440, 1500, 1505, 1605, and 1905 series) are built in three parts. An integral part of our mounts are the connection where the arm and clamp are joined by two assembly bolts located on the underside of the mounts. THESE ASSEMBLY BOLTS ARE NOT MEANT TO BE REMOVED OR TAMPERED WITH AT ANY TIME. The torx head bolts are installed using a permanent thread-lock compound. Doing so will void all warranties. Please contact K-EDGE warranty manager Info@K-EDGE.com for questions or concerns. We highly suggest you follow the recommendations in the Garmin EDGE instructions that recommend use of the provided tether leash.
Replacement plastic insert kit for K-EDGE Wahoo Mounts. The co-polymer insert for Wahoo 1/4-turn style computers is a replaceable item. While it is extremely strong, it is designed to fail on a significant impact before the tabs on the back of the Wahoo break. Attributes (specs): – Qty 1 – K-EDGE Co-polymer Insert for Wahoo 1/4 Computer (Part No. K13-1604) – Qty 2 – M3 x 0.5mm x 6mm with Pre-Applied Nylon 180,18-8 S.S. Screws
Garmin's ANT+ USB stick plugs into your computer's USB port to wirelessly transmit your activities to Garmin Connect and Garmin's Training Center. It automatically receives your activity data when your compatible ANT+ Garmin device is within range.
Monitor your pedaling cadence as you ride with Garmin's easy-to-install wireless sensor. The cadence sensor fastens to any crank arm size and measures pedal strokes per minute so you can get the most out of your training. Simply attach the sensor and ride. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain, and move between bikes.
Garmin's set of Bike Cadence Sensor Replacement Bands fasten your Bike Cadence Sensor (sold separately) to any size crank arm.
Monitor your speed as you ride with this easy-to-install wireless sensor. With no magnets or other exposed parts to line up, this sensor is easy to install, maintain and move between bikes. The speed sensor 2 attaches to the hub of either wheel. You can set up wheel size in our Garmin Connect online community or self-calibrate with an Edge cycling computer or compatible Garmin device. Once set up, you’ll get accurate speed and distance at all times — even without a head unit. ANT+ connectivity and BLUETOOTH Low Energy technology let you sync to Garmin Connect and other training apps, compatible devices and fitness equipment for better data when you ride indoors and outdoors.
Protect your Garmin Edge 1000 with a form-fitting, silicone case and keep your mind at ease. Choose from a variety of cool colors to match your personal style.
Garmin's so-tiny-you-won't-notice-it Foot Pod attaches to your shoe laces and uses ANT+ technology to wirelessly communicate with your watch. This allows you to get run distance and speed when training indoors on the treadmill or when GPS is unavailable. It also provides cadence (foot steps per minute) so you can get accurate data to help you improve. This isn't your average pedometer, as it uses MEMS inertial-sensor technology to accurately analyze stride-length changes and calculate your speed and distance to within 98% accuracy.
Stay ahead of the pack with Garmin's Out-front Bike Mount that lets you to take full advantage of your Edge's capabilities without compromising your ride. The mount positions your device for easier monitoring and safety. Also compatible with the Forerunner 910XT and 310XT when used with a quick-release kit (sold separately).
Mount your Garmin Edge computer with the Quarter Turn Bike Mount. It includes the bike mount, rubber disc, and elastic bands to secure the Quarter Turn to your stem or handlebars.
Protect your Edge 520 with these form-fitting, removable silicone cases.
CatEye's Bluetooth Speed/Cadence Sensor transmits your speed and cadence through your Bluetooth-compatible Smartphone to your handlebar-mounted CatEye Strada Smart cyclo-computer (sold separately). Download the CatEye Cycling app for iPhone/Android and you’ll get all your ride data and save your phone battery. Attack each ride and celebrate your successes on the bike!
- Compatible with Super Record, Record, and Athena EPS systems - Required for use with the charger and works with V2 systems - USA/North America plug - adapters required for other countries
Low Road position places the computer in front of the bar and nearly flush with the top of the bar, making for an easy to read display whether you are on the hoods or in the drops. - Sub-20 gram computer mount - Compatible with computers with 1/4 turn twist lock interface and 31.8mm bar surface - Single Torx T25 fixing bolt
Zipp delivers an uncomplicated computer mount for aerobar extensions that’s easy to install, lightweight, and vibration and slip free. The 22.3mm industry standard mount installs simply and securely on aero extensions. The Zipp QuickView TT Computer Mount is aerodynamically shaped for left-side installation, but also can be installed on the right bar extension. It comes with a single Torx T25 bolt, flexible mounting clamp, and a quarter-twist mount.
With aerobars, short stems and hydration systems crowding the front end of your bike, it's hard to mount a computer. But, with Xlab's Aero Computer Mount Gen 2 you can mount your computer to your stem cap! It's aero because it fits neatly behind aero drink systems and horizontally mounted bottles, and the extra height of the mount makes your computer easier to read. It can also be mounted on the Xlab Torpedo Mini Mount, placing your computer in front in your line of sight. • The Aero Computer Mount, re-designed! Aerodynamically designed and longer to support larger screen computers • Mount in front of Torpedo Systems or on stem bolt • Helps reduce drag from a computer mount with one that was designed with aerodynamics in mind • Mount in front of TORPEDO SYSTEM (sold separately) for optimum viewing. • Mount on stem when using non-XLAB drink systems (sold separately) • Easy to read when in aero position • Fits most computers including the new longer form factor models (sold separately) • Mount is 37 mm wide. Plenty of room to support the popular Garmin computers (sold separately) • Includes hardware and instructions • Weight: 29.5 grams
• When aerobar space is tight, place your computer on top • Tuck straw on either side for best aerodynamics • Fits on TORPEDO SYSTEM 100, TORPEDO SYSTEM 400 & REFILL UPGRADE KIT BOTTLES (each sold separately) • Compatible with most computers, including large screens (sold separately) • Glass-reinforced nylon • Weight: 18.5 grams
Aerodynamic dual-bottle BTA hydration system that features a dynamic, multi-position computer mount to accommodate your changing needs. Raise the computer mount up to tuck in a refill bottle for race day, or lower it down for a standard bottle while maintaining the optimal view for training days. - Telescoping Garmin mount features on-the-go tilt adjust to avoid glare. - Zero-leak design with a sealed viewing window to easily monitor liquid levels, and a leak-free Dolphin Breather Valve that lets air in but doesn't let water out. - Capacity: 26oz (768 mL) - Material: Plate: 6061-T6 Aluminum - Cage: Nylon Composite Vee Cage - Computer Mount: Nylon Composite - Bottle: Lead free, BPA-Free and HDPE food safe certified bottle - Brackets: Nylon composite with Velcro straps coated with no-slip extension grip - Adjustment Width: 75-150mm - Weight: 9.3oz (265g)
Telescoping Garmin Computer Mount for Versa Plates. Raise the computer up for Refill Bottles, or lower it down to clear Standard Bottles. On-the-go tilt adjust to avoid glare. - Telescoping computer mount makes for a seamless switch between Refill or Standard Bottle - Compatible with Garmin bike computers and Multisport Watches - Requires Versa Carbon Mount or Versa Aluminum Mount Telescoping Garmin-Specific Computer Mount - Raise the computer mount up to tuck in a Refill Bottle for race day, or seamlessly lower it down for a Standard Bottle to maintain the optimal view for training days. Compatible with Garmin bike computers and multisport watches. On-the-Go Computer Tilt Adjust - Avoid changing glare with a tilt mechanism for easy adjustments while you ride Arrives Fully Assembled - Few steps required to install and head out on your first ride - Weight: 1.9oz (54g) - Construction: Nylon Composite Includes - Fully assembled computer mount - 2 screw sets: one for Versa Carbon Plates, and one for Versa Aluminum Plates Warranty: Limited Lifetime
Gain more room or find the perfect position for lights, computers, music players, GPS, or whatever, with the Topeak BarXtender. Attaches securely to the handlebars or stem and adjusts for optimum position. - Clamp: Fits 22-38 mm tubes (shims included) - Crossbar: Device mount bar 25.4 mm - Material: Engineering Grade Plastic and Steel - Mount: Handlebar, Handlebar Stem - Size (L x W x H): 18 x 3 x 3 cm, 7.1” x 1.2” x 1.2” (folded) - Size (L x W x H): 13 x 10 x 3 cm, 5.1” x 3.9” x 1.2” (open) - Weight: 116 g / 4.08 oz
Wireless ANT+ cadence transmitter for SIGMA ROX 10 and all other ANT+ compatible devices.
Enjoy easy viewing with the Butler Out Front handlebar mount! Out Front Mount for following models: BC 1909 STS BC 2209 STS ROX 5.0 ROX 6.0 ROX 8 ROX 8.1 ROX 9 ROX 9.1 *Note: not for use with ROX 10.0
$3.50 - $31.50
CR2032 Lithium 3V battery for SIGMA computers, heart rate monitors, transmitters, and Micro Lights. Compatible with: - PC3 - PC4 - PC9 - PC15 - Shape watch - FIT watch - Onyx series HRM's - PC 25.10 - PC 3.11 - PC 10.11 - PC 15.11 - PC 22.13 - RC 1209 - RC 14.11 - RC Move - Micro Lights Not Compatible with: - ROX computers - BC 1909 - BC 2209 - BC 23.16
The cadence magnet pedal insert is designed for tight installation situations. The principle is simple, yet space-saving: the power magnet attaches to any steel pedal spindle by magnetic force alone. From there, it triggers the cadence transmitter with each crank revolution.
Wireless mounting bracket for 2012, 2009 STS & 2006 DTS model computers. Handlebar or stem mount. Compatible models: BC 1106 DTS BC 1606L DTS BC1706HR DTS BC 2006 MHR DTS BC 1009 STS BC 1609 STS BC 8.12 ATS BC 12.12 STS BC 14.12 STS BC 16.12 STS Baseline 1200 plus
Replacement handlebar/stem mount for wireless CR 2450 computers. Compatible devices: ROX 8.0 ROX 9.0 ROX 8.1 Rox 9.1 BC1909HR BC2209MHR ROX 5.0 ROX 6.0
Power Spoke magnet for all Sigma computers. Fits round and bladed spokes.
Shimano Di2 External Battery Mounts - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware
Shimano BT-R1A External Di2 Battery - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware - Di2 External Battery, battery charger, and power cable are universal between Dura-Ace 9070, 7970, Ultegra 6870, 6770 and Alfine Di2 systems - Battery weight: 71 grams
Shimano Di2 External Battery Mount - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware
Connect your PC to CycleOps VirtualTraining.
BLE USB Adapter gives Rouvy virtual training software the ability to seamlessly connect to Bluetooth devices and sensors. The adapter contains a Bluetooth (BLE) radio that allows PCs to communicate with BLE devices, including Saris smart indoor bicycle trainers and power meters. Most importantly, the BLE USB Adapter is necessary to update the firmware Over the Air (OTA) via VirtualTraining for the Hammer and Magnus bike trainers. - Bluetooth adapter for PCs to work with Rouvy - Needed for Over the Air Firmware Updates to Smart Indoor Bike Trainers. - Works with PC desktops and laptops.
The QuickView was designed to put the Garmin Edge Computer out in front of the stem. Fits Garmin 605 and 705. - Glass-filled nylon, stainless steel Torx T25 bolt - Weight: 20g
- Shift buttons mounted to the end of a bar plug - Included wire connects to Blip Box - Fits bars with 19 - 20.5mm inside diameter
SRAM's BlipBox is the control module that turns your triathlon or time trial machine into a wireless missile. Connected to SRAM RED eTap Blip remote shifters, the BlipBox manages the wireless shifting via AIREA, SRAM’s proprietary communication protocol, allowing immediate shifts from nearly any aero position. - BlipBox mount included - Replaces standard drop bar shift levers - Limitless aero configurations - Up to two positions per side - Fits a standard Garmin mount or the included mount
Be it the fireworks of a finale, an ideal rhythm, climbing on the top, or a deep, dark place extracting the last kilojoule of effort on your bike split, you want to adjust your gear with the twitch of a finger. eTap Blip satellite shifters allow you to shift when you want, where you want. - Limitless remote shifting positions for drop and aero bars - Wired shift buttons can be positioned however the rider prefers - Connect to Blip Box or drop bar eTap levers - Compatible with SRAM RED eTap shift/brake controls
SRAM eTap batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes up to 60 minutes to complete.The eTAP Powerpack includes a battery charger, cord, transmitter, and international adaptors (US/EU/GB).
Significantly smaller, the SRAM eTap AXS BlipBox is now easier to integrate — mounting inside a stem faceplate cap, feed box, or frame. It's also AXS enabled, for easy personalization. Simple, intuitive, aero. - Replaces standard drop bar shift levers - Simple and intuitive eTap shift logic - AXS enabled for easy personalization - Limitless aero configurations - Two ports per side for Blips - Fits the included optional stem mount - Compatible with existing eTap Blips and Clics - Mounts inside stem faceplate cap, feed box or frame
- Use to keep Blips in place on handlebars - Fits 31.8mm round portion of drop bar - Clamp mounts directly to bar outside of tape zone - Ideal for use with thumbs or index fingers while hands are on the tops - Right and left specific, just like Blips - Weight: 12 grams (for pair) - Material: Polypropylene - Compatibility: 11-speed - Recommended Group: SRAM RED eTap
External Blip mount for aero extensions and base bars - 360 degree rotation for adjustment - Aero use only to fit 22.2mm OD bar 65mm in length - Fits all Zipp aero extensions and base bars - Blips not included - Weight: 57 grams for pair (does not include Blip) - Material: Polypropylene + TPE - Compatibility: 11-speed - Recommended Group: SRAM RED eTap
- For charging batteries in European countries
Free up bar space and secure your GoPro and many other stem-mounted accessories with our Ritchey Universal Stem Mount. Our unique mount means clutter- and hassle-free mounting of your favorite devices where they're easily viewed and operated. - Compatible with Ritchey C220 and 4-Axis 44 stem faceplates - Forged and machined alloy - Includes extended-length hardware
ShockWiz is a suspension tuning system for air-sprung mountain bikes that combines high-tech hardware with an intuitive smartphone app. It's lightweight, durable and powered by a long-lasting coin cell battery, ShockWiz automatically records and evaluates suspension performance every time you ride. The ShockWiz app displays straightforward adjustments that unite bike, terrain and riding style. ShockWiz works for all mountain bike riders, regardless of their experience or bike's intended use. It works on hardtail and dual suspension bikes, and for all levels of skill, speed, and terrain. With ShockWiz, you know exactly how your suspension is performing – and how to make it better. Features & Benefits: - Automated tuning recommendations - Shock tuning score - a snapshot of how well your suspension is set up for you - Works on hardtail and dual suspension bikes. Works for Cross-Country, Trail, All Mountain and Downhill. - Inexpensive, replaceable CR2032 battery lasts for months - Waterproof and dustproof - IP67 rating - Two alternative hoses (included) offer a range of fitting options - Smartphone app is compatible with Apple and Android phones Essential Details: - ShockWiz is designed for all mountain bike riders, regardless of your experience or bike's intended use. - You can tune for every riding style: Efficient (pedaling), Balanced, Playful or Aggressive. - Advice for air pressure, spring rate, compression and rebound is displayed in the intuitive smartphone app. - In the box: ShockWiz hardware, two hoses, rubber mounting boot and zip ties.
ShockWiz is a suspension tuning system for air-sprung mountain bikes that combines high-tech hardware with an intuitive smartphone app. Lightweight, durable and powered by a long-lasting coin cell battery, ShockWiz automatically records and evaluates suspension performance every time you ride. The ShockWiz app displays straightforward adjustments that unite bike, terrain and riding style. ShockWiz works for all mountain bike riders, regardless of their experience or bike's intended use. It works on hardtail and dual suspension bikes, and for all levels of skill, speed and terrain. With ShockWiz, you know exactly how your suspension is performing – and how to make it better. The Direct Mount version is for inverted forks such as the RockShox RS-1. Features & Benefits: - Automated tuning recommendations. - Shock tuning score - a snapshot of how well your suspension is set up for you. - Works on hardtail and dual suspension bikes. Works for Cross-Country, Trail, All Mountain and Downhill. - Inexpensive, replaceable CR2032 battery lasts for months. - Waterproof and dustproof - IP67 rating. - Two alternative hoses (included) offer a range of fitting options. - Smartphone app is compatible with Apple and Android phones. Essential Details: - ShockWiz is designed for all mountain bike riders, regardless of your experience or bike's intended use. - You can tune for every riding style: Efficient (pedaling), Balanced, Playful or Aggressive. - Advice for air pressure, spring rate, compression and rebound is displayed in the intuitive smartphone app. - In the box: ShockWiz hardware, two hoses, adapter for conventional forks and rear shocks, rubber mounting boot and zip ties.
Spare parts for Quarq's ShockWiz automated suspension tuning device. - Contains a rubber mounting boot, four zip ties, plastic cap and two o-rings.
Spare hose kit for Quarq's ShockWiz automated suspension tuning device. - Contains one of each hose type and four zip ties.
Profile Design's UCM Universal Computer Mount provides a convenient 25mm long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.
Profile Design's UCM XL Universal Computer Mount provides a convenient 60mm-long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.
The Under Stem Mount allows riders to secure a Shimano Di2 Junction Box to their bike quickly and easily without the need for zip ties, duct tape, or other unreliable attachments. - Lightweight alloy headset spacer with nylon body (9g) - Compatible only with Shimano Di2 Junction Box - 95mm length, 44mm width, 6mm height - 6 Degree angle
• To position the Shimano Di2 battery inside the fork steerer • Including stainless steel tool to remove the set.
The Vibe Aero Race Mount is designed for the PRO Vibe Aero handlebar/stem combination. Made of high-quality CNC machined 6061-T6 Aluminum, it fits all Pro handlebar/stem combinations. - Compatibility (Regular): GARMIN 820, 520, 25, 20 - Compatibility (XL): GARMIN 1030, 1000, 820, 520, 25, 20 - Lifetime Guarantee - Weight: 30g
Wire harness and hardware to measure computer data based on the front wheel. - Fits most bars bars (25.0 to 31.8mm), 86cm wire, wheel magnet (fits up to 4mm bladed spokes) and zip ties - Compatible with: Protege 5.0, 8.0 and 9.0
Protege wire harness and hardware with extra length for use with tandem and recumbent bicycles - Contains bracket with 160cm wire, wheel magnet and zip ties - Brackets fits Standard (25.4-26.0mm) bars - Compatible with: Protegé 5.0, 8.0 and 9.0 - Ideal for long wheelbase recumbent and computer installs on a tandem’s rear bars
- Contains universal handlebar/stem compatible bracket, sensor and magnet - Compatible with Protege 9.0 wireless computer - Will not convert standard Protege 9.0 to wireless
Page 1 of 3 Next page